In the Idle Air write up there are two references to the SPOUT connector for measuring the AM for non mechanical idle:
If you so choose to dial in the airmass and throttle body airflow while custom tuning you must plug in the IAC, TPS, and SPOUT to calculate idle airmass.
... and later:
You must temporarily lock out the ignition timing to get an accurate idle airmass, this can be achieved by either removing the SPOUT CONNECTOR
Given the reference to locking timing at 10*, I am assuming the SPOUT needs to be disconnected, but IAC and TPS would remain. Is that correct?
Dialling in Idle Air
-
- Posts: 104
- Joined: 2021 Feb 15, 21:56
- Location: Lancaster New York
- Vehicle Information: 1989 fox GT convertible
5.0 stock block, E7 heads, stock cam
Explorer GT40 intake flipped to driver side inlet
Single 67mm On3 BB turbo
Flipped JBA headers, custom SS 2.5" hotside built by me
custom 3" coldside thru On3 intercooler
tuning with Moates QH + TPRT
Dechipa's GUFX and supporting files, couldnt have tuned it myself without him!
Re: Dialling in Idle Air
If you are running deciphas A9L2 and mechanical idle then disregard that you just pay attention to the logged idle airmass correction.
If you’re still working with stock idle setup then yes spout comes out and iac disconnected. Disconnect tps if you need to open the throttle blade while the engine is running
If you’re still working with stock idle setup then yes spout comes out and iac disconnected. Disconnect tps if you need to open the throttle blade while the engine is running
-
- Posts: 17
- Joined: 2021 Feb 27, 06:15
- Location: Palm Beach
- Vehicle Information: Cobra. 5.0. TFS Heads and cam. MassFlo (ProM) EFI.
Re: Dialling in Idle Air
Thanks, PaulC
To clarify, I am banging on the original A9L tune. I am not using mechanical idle (yet).
My query is not actually about the adjusting the idle screw, but measuring airmass at idle to update the FN875N table.
Given the timing lockout is required, reckon I'll just remove the SPOUT and leave the IAC and TPS.
To clarify, I am banging on the original A9L tune. I am not using mechanical idle (yet).
My query is not actually about the adjusting the idle screw, but measuring airmass at idle to update the FN875N table.
Given the timing lockout is required, reckon I'll just remove the SPOUT and leave the IAC and TPS.
-
- Posts: 104
- Joined: 2021 Feb 15, 21:56
- Location: Lancaster New York
- Vehicle Information: 1989 fox GT convertible
5.0 stock block, E7 heads, stock cam
Explorer GT40 intake flipped to driver side inlet
Single 67mm On3 BB turbo
Flipped JBA headers, custom SS 2.5" hotside built by me
custom 3" coldside thru On3 intercooler
tuning with Moates QH + TPRT
Dechipa's GUFX and supporting files, couldnt have tuned it myself without him!
Re: Dialling in Idle Air
My bad guess I didn’t read your OP clearly enough.
-
- Posts: 468
- Joined: 2021 Mar 21, 15:17
- Location: Colorado Springs, CO
- Vehicle Information: 95 Mustang GT, CBAZA Quarterhorse
331, 190 11R heads, Edelbrock Victor 50 manifold, F303, T5, 76mm Turbo, 91 octane, Returnless dual pump 03 cobra tank, Behind bars rails, 80# siemens injectors
wbo2_030MtxL
57 F100, RZASA, 04 Crown Vic ecu and harness, 302, GT40 heads, 4r70w, 80# deka5 shorties, Holley carb style throttle body, Speedmaster high rise intake manifold
Re: Dialling in Idle Air
You unplug the iac and the spout and then log the maf air flow when the car is at operating temperature. You may even have to do something with the pcv valve since it also is pulling in fresh air which would skew the results of the TB airmass.
-
- Posts: 17
- Joined: 2021 Feb 27, 06:15
- Location: Palm Beach
- Vehicle Information: Cobra. 5.0. TFS Heads and cam. MassFlo (ProM) EFI.
Re: Dialling in Idle Air
Thank you both, that makes sense. Much appreciated.