Search found 7 matches
- 2023 Nov 30, 11:15
- Forum: PCM / ECU / EEC Tuning
- Topic: Lopping at idle
- Replies: 13
- Views: 4699
Re: Lopping at idle
Should I have erased KAM memory before I loaded the last tune you sent me ? or dose that really matter.
- 2023 Nov 28, 20:26
- Forum: PCM / ECU / EEC Tuning
- Topic: Lopping at idle
- Replies: 13
- Views: 4699
Re: Lopping at idle
I wasn't closing it, I opened it more. The TPS and IAC was unplugged when I made the adjustment the truck was just under desired RPM at idle, about 700 RPM then I turned the engine off and plugged everything back in and tired to start the truck and would not do anything but crank. It was turning over like I had the pedal to the floor. That's never happened before until I loaded the last tune in it.
- 2023 Nov 28, 10:53
- Forum: PCM / ECU / EEC Tuning
- Topic: Lopping at idle
- Replies: 13
- Views: 4699
Re: Lopping at idle
Could the TPS have a bad spot in it, I don't think it is a motorcraft TPS.
but it didn't do it before I uploaded the last tune you sent me.
but it didn't do it before I uploaded the last tune you sent me.
- 2023 Nov 28, 08:42
- Forum: PCM / ECU / EEC Tuning
- Topic: Lopping at idle
- Replies: 13
- Views: 4699
Re: Lopping at idle
Where in my tune can I adjust the idle down table so it is smoother when the truck idles down from a rev.
it is jumpy when the truck idles down.
also I made a small idle adjustment at the throttle blade and the truck would not restart until I put it back in the same spot, what is going on with that.
I am using SCT software .
it is jumpy when the truck idles down.
also I made a small idle adjustment at the throttle blade and the truck would not restart until I put it back in the same spot, what is going on with that.
I am using SCT software .
- 2023 Nov 21, 07:58
- Forum: PCM / ECU / EEC Tuning
- Topic: Lopping at idle
- Replies: 13
- Views: 4699
Re: Lopping at idle
I don't see my section or strategy. Where should I be posting in.
- 2023 Nov 20, 15:24
- Forum: PCM / ECU / EEC Tuning
- Topic: Lopping at idle
- Replies: 13
- Views: 4699
Re: Lopping at idle
Where are the tables located in SCT and how do I know what to change them too.
Side note I am not new to tuning BUT I still have a lot to learn so if I say something stupid my bad.
I am still trying to figure out what everything is and dose, there is a lot of info on this forum.
Side note I am not new to tuning BUT I still have a lot to learn so if I say something stupid my bad.
I am still trying to figure out what everything is and dose, there is a lot of info on this forum.
- 2023 Nov 20, 09:10
- Forum: PCM / ECU / EEC Tuning
- Topic: Lopping at idle
- Replies: 13
- Views: 4699
Lopping at idle
Hello everyone I am have a issue with my truck. I can't figure out why it's loping at idle and some times when I come to a stop.
I have changed the idle control settings and IAC duty cycle back to stock with no change. The truck has a brand new motor craft IAC valve.
The truck is turbocharged and tuned with SCT.
PLEASE HELP !!!!
I have changed the idle control settings and IAC duty cycle back to stock with no change. The truck has a brand new motor craft IAC valve.
The truck is turbocharged and tuned with SCT.
PLEASE HELP !!!!