Search found 24 matches
- 2024 Jun 01, 13:20
- Forum: Moates Support
- Topic: J3 Chip Availability
- Replies: 3
- Views: 96
- 2024 May 30, 17:39
- Forum: Moates Support
- Topic: J3 Chip Availability
- Replies: 3
- Views: 96
J3 Chip Availability
Good afternoon Mr. Decipha
Long shot but do you have any F3 chips available? I need one.
Thank you MB
Long shot but do you have any F3 chips available? I need one.
Thank you MB
- 2024 Jan 13, 13:25
- Forum: FBGI0 - 02-04 Mustangs (ALL)
- Topic: Mach 1 CR
- Replies: 11
- Views: 5867
Re: Mach 1 CR
Ye MMR has 4.75 Stroker kit that uses that crank kit,,, OIL PUMP
- 2023 Dec 18, 08:16
- Forum: Speed Shop & Engine Talk
- Topic: Loose valve seats (4V 4.6)
- Replies: 5
- Views: 2903
Re: Loose valve seats (4V 4.6)
I would reach out to modular head shop for your cylinder head Questions.
I spoke with them when I was going to have them do my cylinder head work done for my current build but decided to use the new heads I have from my previous build.
www.modularheadshop.com
I have heard of valve seats coming loose on these heads that have some miles on them. Sorry to hear about your mishap. Keep us posted on your build...
MB
I spoke with them when I was going to have them do my cylinder head work done for my current build but decided to use the new heads I have from my previous build.
www.modularheadshop.com
I have heard of valve seats coming loose on these heads that have some miles on them. Sorry to hear about your mishap. Keep us posted on your build...
MB
- 2023 Dec 17, 14:57
- Forum: FBGI0 - 02-04 Mustangs (ALL)
- Topic: Mach 1 CR
- Replies: 11
- Views: 5867
Re: Mach 1 CR
Well, I ordered my 5.0 forged stroker kit .020 over Manley flat tops pistons with king bearings from ModMax Racing.
I will use ARP handwear and have the rotating assembly balanced.
Kook LT 3" Kooks x pipe Todd Waren spec N/A cams. 65mm BBK TB #30 injectors 90mm maf sensor
When all said and done, I will be reaching out to Mr. Decipha for one of his remote tunes VIA QH to help me dial it in.
Should be a good street combo.
MB
I will use ARP handwear and have the rotating assembly balanced.
Kook LT 3" Kooks x pipe Todd Waren spec N/A cams. 65mm BBK TB #30 injectors 90mm maf sensor
When all said and done, I will be reaching out to Mr. Decipha for one of his remote tunes VIA QH to help me dial it in.
Should be a good street combo.
MB
- 2023 Dec 12, 18:41
- Forum: Hardware, Programming & Disassembly
- Topic: 2009 Ford Shelby needs pcm....
- Replies: 1
- Views: 1160
2009 Ford Shelby needs pcm....
Sorry, I may be out of line here but I'm up against the wall. I have a 09 Shelby that the pcm is bad crank no start. Nobody has one. Is there any options here? Help!
Thank you MB
Thank you MB
- 2023 Dec 08, 07:14
- Forum: GUFX - 89-93 Foxbody ECUs
- Topic: Wide band
- Replies: 1
- Views: 1646
Wide band
If you were to install a wide band, Is there a preference on what side? And why? I have lt headers.
Thanks MB
Thanks MB
- 2023 Nov 27, 08:39
- Forum: FBGI0 - 02-04 Mustangs (ALL)
- Topic: Mach 1 CR
- Replies: 11
- Views: 5867
Re: Mach 1 CR
My last build was with MMR 4.75 stroker kit for my 03 Cobra with a gen 3r 2.65 VMP
- 2023 Nov 27, 08:35
- Forum: FBGI0 - 02-04 Mustangs (ALL)
- Topic: Mach 1 CR
- Replies: 11
- Views: 5867
Re: Mach 1 CR
I did not realize you can use gen 3 coyote rods and pistons for my engine block.m-barans wrote: ↑2023 Nov 26, 21:53 I plan on doing a similar build. I purchased pistons from mod max and am pleased with the cp pistons they offered. If I was to go again (especially NA) I would go with custom mmr (manleys) and a coyote crankshaft with gen 3 coyote rods. To answer your question: 11:5 to 1 static compression ratio is probably fine. Less spark advance may be in order to reach mbt, Sounds like a coyote numbers because it basically is less the variable cam timing. Jmho
Humm Maybe a call into MMR and see what they suggest.
Ty Mb
- 2023 Nov 26, 19:18
- Forum: FBGI0 - 02-04 Mustangs (ALL)
- Topic: Mach 1 CR
- Replies: 11
- Views: 5867
Re: Mach 1 CR
Question How high can I go on CR 04 Mach1 using 93 pump gas? and or E85 fuel?
I am in the process of rebuilding my motor, stock CR for Mach1 is 10.1 and I would like to add little more compression...
Currently I have Kooks LT 3" collectors 3: x pipe, Todd Warren cams, BBK 65MM Throttle Body, 4.56 gears 5s speed.
I see that on ModMax Racing website they show using Manley flat top Pistons obtaining 11.17:1 CR for a 4.6 4v motor.
I will be using QH
Thank you
MB
I am in the process of rebuilding my motor, stock CR for Mach1 is 10.1 and I would like to add little more compression...
Currently I have Kooks LT 3" collectors 3: x pipe, Todd Warren cams, BBK 65MM Throttle Body, 4.56 gears 5s speed.
I see that on ModMax Racing website they show using Manley flat top Pistons obtaining 11.17:1 CR for a 4.6 4v motor.
I will be using QH
Thank you
MB