Search found 104 matches
- 2024 Mar 14, 10:29
- Forum: The Range
- Topic: Minimal posts
- Replies: 10
- Views: 3598
Re: Minimal posts
ive always been interested in the premium side but can understand why its kept private. I dont see the disgruntled guys post to check out?
- 2023 Nov 05, 14:38
- Forum: A1C - 80/90s EFI-SD4x Speed Density
- Topic: Inferior software?
- Replies: 3
- Views: 1674
Re: Inferior software?
I had a similar experience calling a local dyno shop. Just wanted to get dyno numbers and see if minor tune tweaks would pick anything up. He may have taken it that I wanted him to do the tuning changes but man he seemed turned off when I told him about my car, mainly the stock ecu and wiring. Wanted to still take it there to show him how nice the car is and how good it runs but never did.
- 2023 Jul 05, 09:11
- Forum: GUFX - 89-93 Foxbody ECUs
- Topic: Using IAT in Slot MAF and Wideband question
- Replies: 2
- Views: 2981
Re: Using IAT in Slot MAF and Wideband question
I switched mine to the iat of the slot maf and you get much more accurate readings. You’ll want to adjust the temps it pulls timing to lower numbers though.
And no the narrowbands are still needed, that just allows you to datalog the wideband.
And no the narrowbands are still needed, that just allows you to datalog the wideband.
- 2023 May 31, 10:31
- Forum: CDAN4 - 96/97 Fords (Most All)
- Topic: Tune
- Replies: 5
- Views: 6126
Re: Tune
Glad to see an update here. Dave is my welding supplier at work and I recommended you to him for this project.
- 2023 Mar 02, 11:09
- Forum: FBGI0 - 02-04 Mustangs (ALL)
- Topic: Inferred Ambient ACT
- Replies: 13
- Views: 5683
Re: Inferred Ambient ACT
Although I dont recall seeing the crazy iat's you are I dealt with similar fueling issues due to heat soak. I re-wrapped my hotside last winter and this time around also wrapped the headers, they were just heat painted previously. That change has seemed to help out alot as my fuel trims didnt move around nearly as much last summer.
- 2023 Jan 13, 07:18
- Forum: A1C - 80/90s EFI-SD4x Speed Density
- Topic: Electric fan control on Sd4x
- Replies: 48
- Views: 15770
Re: Electric fan control on Sd4x
Im sure this will be a more expensive route then what you're looking at but this is a top notch stand alone controller. after many setups with cheap controllers and relays I went to one of these and have been very happy. The PMW control and soft start features are super nice. I went with one of his sensors that goes inline with the lower radiator hose but you could possibly save money there and use the ecu temp sensor instead?
https://www.autocoolguy.com/home
https://www.autocoolguy.com/home
- 2022 Nov 30, 14:32
- Forum: Speed Shop & Engine Talk
- Topic: 4.6 DOHC Noise
- Replies: 9
- Views: 4798
Re: 4.6 DOHC Noise
You should run yours stock being N/A. The Decipha way I mentioned is specifically for boost. I think the details are in the getting started write up.
- 2022 Nov 30, 12:25
- Forum: Speed Shop & Engine Talk
- Topic: 4.6 DOHC Noise
- Replies: 9
- Views: 4798
Re: 4.6 DOHC Noise
my guess would be pcv system. on my turbo fox, much different pcv setup being turbo, I run it the way Decipha recommends and when I had the system mostly sealed up it would create an odd whistle shortly after starting, which would then go away, but on shut down it would bleed off and whistle like you're describing. I couldnt stand it so and couldnt figure out where it was coming from so I popped a few tiny holes in the line to the oil filler neck which thankfully made it stop.
- 2022 Oct 04, 08:09
- Forum: GUFX - 89-93 Foxbody ECUs
- Topic: Dialling in Idle Air
- Replies: 5
- Views: 2495
Re: Dialling in Idle Air
My bad guess I didn’t read your OP clearly enough.
- 2022 Oct 03, 08:23
- Forum: GUFX - 89-93 Foxbody ECUs
- Topic: Dialling in Idle Air
- Replies: 5
- Views: 2495
Re: Dialling in Idle Air
If you are running deciphas A9L2 and mechanical idle then disregard that you just pay attention to the logged idle airmass correction.
If you’re still working with stock idle setup then yes spout comes out and iac disconnected. Disconnect tps if you need to open the throttle blade while the engine is running
If you’re still working with stock idle setup then yes spout comes out and iac disconnected. Disconnect tps if you need to open the throttle blade while the engine is running