Search found 17 matches

Return to advanced search

For Sale- Quarterhorse, A3M eec, Pmas hpx-e

I have a Moates Quarterhorse (newer one with replaceable battery) and A3M eec out of my 93 mustang 5 speed, also have Pmas hpx-e in a 80mm housing for sale. Everything works perfectly,it is still installed in the car. If you need pictures I can email or text them to you. Quarterhorse- $150 A3M- $200...
by vcoupe
Fri May 17, 2019 9:22 pm
 
Forum: For Sale / Wanted
Topic: For Sale- Quarterhorse, A3M eec, Pmas hpx-e
Replies: 1
Views: 467

Re: bosch high impedance 2200 cc injectors

Would you mind posting the injector data that you used for those injectors.
by vcoupe
Fri Mar 29, 2019 7:59 am
 
Forum: General Hardware
Topic: bosch high impedance 2200 cc injectors
Replies: 9
Views: 984

Re: Hpx-e close to being pegged

Also one more thing, I found a deal on some FIC 1200cc injectors and will be stepping up to those from 80lbers. Will it be difficult to get them to idle out? I will be on e85. Thanks for your responses.
by vcoupe
Wed Feb 13, 2019 2:22 pm
 
Forum: Foxbody Tuning (GUFX)
Topic: Hpx-e close to being pegged
Replies: 7
Views: 1005

Re: Hpx-e close to being pegged

If I decide to upgrade to a 4 inch housing, will run into any problems dialing it back in as far as resolution?
by vcoupe
Wed Feb 13, 2019 11:39 am
 
Forum: Foxbody Tuning (GUFX)
Topic: Hpx-e close to being pegged
Replies: 7
Views: 1005

Re: Hpx-e close to being pegged

My maf pegs at 4.7 volts, the last time I pegged my maf it was at 4.7 volts. I am guessing because of the resistance in the wires.
by vcoupe
Wed Feb 13, 2019 8:32 am
 
Forum: Foxbody Tuning (GUFX)
Topic: Hpx-e close to being pegged
Replies: 7
Views: 1005

Hpx-e close to being pegged

I took a log at 18lbs of boost and my mafv is at 4.5v at 5300rpm, my hpx-e is in a 85mm housing, should I just put it in a 4inch tube? Will I have problems with it being in such a big housing? What options do I have? Or should I not worry about it until I make a full pull to 6000rpm.
by vcoupe
Tue Feb 12, 2019 11:51 am
 
Forum: Foxbody Tuning (GUFX)
Topic: Hpx-e close to being pegged
Replies: 7
Views: 1005

Re: turbo 2v tuning

In the base tune on the FN1262x table there are zeros on the rpm and loadx axis. So how to do I fill them with the appropriate valves?
by vcoupe
Sun Dec 16, 2018 12:58 pm
 
Forum: EEC-V & SN95 Tuning
Topic: turbo 2v tuning
Replies: 6
Views: 863

Re: turbo 2v tuning

So I started navigating through it, FN1362X which I am assuming is my commanded LAMBDA table. The problem is I am trying to figure out how to scale the load and rpm axis. What Functions do I use?
by vcoupe
Sat Dec 15, 2018 5:08 pm
 
Forum: EEC-V & SN95 Tuning
Topic: turbo 2v tuning
Replies: 6
Views: 863

turbo 2v tuning

My buddy has a 2001 bullitt mustang turbo 2v and I am trying to help him out. I am pretty familiar with QH and Gufb because this is how I tuned my car. I have couple questions if anyone can help. 1) How similar is the tuning to Gufb? 2) What would be the best way to start out in tackling this? 3) Wi...
by vcoupe
Sat Dec 15, 2018 9:14 am
 
Forum: EEC-V & SN95 Tuning
Topic: turbo 2v tuning
Replies: 6
Views: 863

Re: Fan control not working

I feel like an idiot, I don't know how I misunderstood that. Thank you so much.
by vcoupe
Fri Nov 23, 2018 4:10 pm
 
Forum: Foxbody Tuning (GUFX)
Topic: Fan control not working
Replies: 10
Views: 1423

Re: Fan control not working

Yes I did, but when enable those scalers, and reach the temperature I target the eec does not throw ground to pin 41. Mybe my eec is damaged in that area. It is just weird when I disable those scalers I get constant ground through pin 41.
by vcoupe
Thu Nov 22, 2018 7:18 pm
 
Forum: Foxbody Tuning (GUFX)
Topic: Fan control not working
Replies: 10
Views: 1423

Re: Fan control not working

With fan control turned off is pin 41 supposed to throw ground?
by vcoupe
Thu Nov 22, 2018 1:21 pm
 
Forum: Foxbody Tuning (GUFX)
Topic: Fan control not working
Replies: 10
Views: 1423

Re: Fan control not working

No I am not using a9l2. My grounds seem fine.
by vcoupe
Thu Nov 22, 2018 9:48 am
 
Forum: Foxbody Tuning (GUFX)
Topic: Fan control not working
Replies: 10
Views: 1423

Re: Fan control not working

Yes sir, I have triple checked every thing with the write up. You would think when it reaches the temp I plug in it would do something. So it looks like the eec never latches ground unless fan control is disabled. I cut the wire going from the relay to the pin 41 and grounded the relay wire and it k...
by vcoupe
Wed Nov 21, 2018 1:42 pm
 
Forum: Foxbody Tuning (GUFX)
Topic: Fan control not working
Replies: 10
Views: 1423

Fan control not working

So I wired up a relay to pin 41 as the instructions said in the write up. The problem I am having is as soon as I load the tune in the fans turn off and they do not turn back on no matter what temperature I plug in. I have read the write up several times and triple checked my wiring and pin 41. If I...
by vcoupe
Wed Nov 21, 2018 1:23 pm
 
Forum: Foxbody Tuning (GUFX)
Topic: Fan control not working
Replies: 10
Views: 1423

hpx-e or bigger housing

I pegged my pmas hpx in a 85mm housing should I go hpx-e or 95mm housing?
by vcoupe
Fri Feb 23, 2018 8:59 pm
 
Forum: Foxbody Tuning (GUFX)
Topic: hpx-e or bigger housing
Replies: 1
Views: 792

trying to log fuel pressure

I am trying to log fuel pressure through the egr pin27 output. Does anyone know what pin to tap into for 5v power source?
by vcoupe
Mon Jan 23, 2017 6:04 pm
 
Forum: Foxbody Tuning (GUFX)
Topic: trying to log fuel pressure
Replies: 1
Views: 756

Return to advanced search